Seletividade com fusíveis

Como obter seletividade com fusíveis

Aqui você encontra as regras para projeto de seletividade entre fusíveis ou entre fusíveis e disjuntores. Há três combinações possíveis:

Fusíveis a montante e a jusante
Como projetar seletividade nas zonas de sobrecarga e de curto
Disjuntor a montante e fusível a jusante
Como projetar seletividade nas zonas de sobrecarga e de curto
Fusível a montante e disjuntor a jusante

Fusível / Fusível

Disjuntor / Fusível

Fusível / Disjuntor

Fusíveis a montante e a jusante

Seletividade na zona de sobrecarga

Seletividade na zona de curto

Fusíveis da mesma categoria de utilização e diferentes correntes nominais têm características paralelas; a seletividade é obtida por comparação entre as características tempo-corrente.

É preciso conferir as curvas tempo-corrente para fusíveis de diferentes categorias de utilização (por exemplo, aM e gG), não pode haver superposição.

Essa verificação da seletividade entre fusíveis é válida para tempos de operação t ≥ 0,1 s.

Determina-se a seletividade a partir das características de energia circulante I²t.

A corrente limite de seletividade é o valor para o qual o I²t de operação total do fusível a jusante excede o I²t pré-abertura de arco do fusível a montante.

Na zona de curto a energia circulante por um fusível é constante e, por isso, a comparação é possível entre os valores tabelados informados pelo fabricante. I²t pré-arco independe da tensão e da corrente nesta zona, mas I²t de abertura de arco depende da tensão do sistema, o que afeta o valor operacional total.

No caso de fusíveis do mesmo tipo (por exemplo, gG – gG) aderentes à IEC 60269-2, verifica-se seletividade total quando a corrente nominal do fusível a montante é de 1,6 vezes a corrente nominal do fusível a jusante.

Disjuntor a montante e fusível a jusante

Seletividade na zona de sobrecarga

Seletividade na zona de curto

Verificamos a seletividade comparando as características tempo-corrente

Aconselha-se manter uma margem de segurança entre o tempo de disparo máximo da característica do fusível e o tempo de disparo mínimo da característica do disjuntor.

Em geral, um delta tempo ≥ 1s basta para disjuntores termomagnéticos e 100ms bastam para as unidades de disparo eletrônicas.

Verifica-se a seletividade na zona de curto por comparação entre as características tempo-corrente, no caso dos disjuntores com abertura da proteção com tempo de atraso (proteção S, Código ANSI 50TD).

Na zona de disparo instantâneo e para disjuntores sem atraso na abertura do curto, o limite de corrente para seletividade deve ser estabelecido a partir dos dados de teste entregues pelo fabricante.

Na ausência de dados de teste específicos, a garantia da seletividade se dá até o nível de corrente de falha em que a corrente de pico circulante pelo fusível a jusante seja inferior ao valor de pico correspondente ao nível de disparo instantâneo do dispositivo a montante.

Ipk (fusível) ≤ I3 (disjuntor)

Fusível a montante e disjuntor a jusante

Seletividade na zona de sobrecarga

Seletividade na zona de curto

Ocorre principalmente quando o fusível a montante é usado como proteção reserva dos disjuntores, em caso de níveis de falha prospectivos excepcionalmente elevados.

Na zona de sobrecarga a seletividade é determinada a partir da comparação entre as características tempo-corrente.

Está relacionada às características de energia circulante I²t.

O limite de corrente para seletividade é o valor para o qual a energia circulante ^I2t pelo disjuntor excede o valor de pré-arco de I²t para o fusível (curva ou valor informado pelo fabricante).

Atenção:
Para garantir total seletividade entre o fusível a montante e o disjuntor a jusante, recomendamos a troca do fusível a montante depois que um curto-circuito é aberto pelo disjuntor a jusante.

This technical report, which serves as an application guide for the determination of selectivity between over-current protective devices of low-voltage switchgear and controlgear, summarises the definitions of the terminology and provides examples of application. This report does not deal with other forms of protection, such as power-reversal protection, directional protection and arc-protection systems.

Selectivity between circuit-breakers
Methods for the determination of selectivity between circuit-breakers, for the overload zone of operation, and for the fault current zone of operation, are given below.

UD = Upstream device:
in considering selectivity between two OCPDs (over-current protective devices), the OCPD connected in the circuit nearest to the source of supply.

DD = Downstream device:
in considering selectivity between two OCPDs (over-current protective devices), the OCPD connected in the circuit immediately following the upstream device, on the load side.

Overload zone (of over-current):
range of current, exceeding the rated current of the OCPD (over-current protective device), produced by the circuit loading in the absence of a fault in the circuit.

Fault current zone (of over-current):
range of current exceeding the overload current, produced by a fault in the circuit.

4.1 Circuit-breakers – Selectivity in the overload zone
Selectivity in the overload zone is verified by comparison of the time/current characteristics, see Figure 1a and Figure 1b (Figure 1b is applicable to moulded case circuit-breaker and air circuit-breaker only). Separation of the characteristics in both the time and current axes ensures selective operation of DD with respect to UD, in this zone. There will be a tolerance applicable to the characteristic, which should be taken into account. The manufacturer’s data should show a tolerance band or otherwise indicate the tolerance applicable, as required by the product standard.

Comparison of the operating characteristics of circuit-breakers in the overload zone.

Figure 1a

Comparison of thermal time/current characteristics in the overload zone

Figure 1b

Comparison of electronic time/current characteristics in the overload zone

NOTE:

The characteristics are subject to tolerances, which must be taken into account
It is necessary that the current scales are in amperes (or kA) for comparison of these curves. Manufacturer’s published characteristics may be given in either amperes or multiples of rated current.
A combination of thermal/magnetic and electronic characteristics is also commonly used.

4.2 Circuit-breakers – Selectivity in the fault current zone
Selectivity between circuit-breakers is elaborated in the product standards IEC 60947-2, Annex A and IEC 60898-1, Annex D, specifying the tests, where applicable, which show determination of selectivity in the fault-current zone. The methods applicable are mentioned hereunder.

NOTE:

Due to their basic construction MCBs to IEC 60898-1 are generally highly selective against MCCBs to IEC 60947-2.

4.2.1 Circuit-breakers – Selectivity determination in the fault current zone by comparison of characteristics
Determination from characteristics of selectivity between two circuit-breakers in the fault current zone, is limited to the case where UD has a short-circuit release time-delay function provided by an electronic release. Selectivity at fault currents producing instantaneous tripping of UD, for both electronic and electromagnetic releases, needs to be determined from test data provided by the manufacturer.

4.2.2 Circuit-breakers – Selectivity determination by test in the fault current zone at fault currents producing instantaneous tripping
For each combination of circuit-breakers, the selectivity limit currents is determined from test and the manufacturer will supply data, usually in the form of a chart. In each case selectivity may be total or partial as follows:

total selectivity: this means selectivity for all over-currents up to the value of the breaking capacity, i.e. DD alone will operate (to the TRIPPED position) on over-current up to this level.
partial selectivity: this means selectivity up to a value of over-current less than the breaking capacity of DD. The selectivity limit current is obtained by comparison of time/current characteristics or, in the case of instantaneous tripping of UD, from data obtained from tests and provided by the manufacturer.

NOTE:

The data for selectivity limit current in the fault current zone producing instantaneous tripping of the circuit-breaker is obtained from test data and is specific to each device type. There is no recognized method of substitution for devices of different manufacture.
Proprietary software systems for determination of selectivity are available, working from time/current data supplied by individual manufacturers.

For more information see the IEC/TR 61912-2 Edition 1.0

Zone selectivity

Introduction

Operatively speaking

This type of coordination is an evolution of time coordination.
In general, zone selectivity is realized by means of dialogue between the current measuring de-vices that, once the setting threshold has been detected as having been exceeded, allows the fault zone to be identified correctly and the power supply to the fault to be cut off.

It can be realized in two ways:

The measuring devices send the information on the current setting threshold having been exceeded to a supervision system and the latter identifies which protection has to intervene;
When there are current values exceeding their setting, each protection sends a lock signal by means of a direct connection or a bus to the hierarchically higher level protection (on the supply side in relation to the power flow direction) and, before intervening, checks that a similar lock signal has not arrived from the load-side protection. Thus, only the protection immediately on the supply side of the fault trips.

This second way guarantees without doubt shorter trip times. Compared with a coordination of the time type, the need to increase the intentional delay as one moves towards the power supply source is no longer necessary. The delay can be decreased to the time needed to exclude the presence of a possible lock signal coming from the load-side protection.
This type of selectivity is suitable for radial networks and, when associated with directional protec-tion, is suitable for meshed networks too.

Compared with the coordination of time type, zone selectivity permits:

a reduction in the trip times (these can be lower than hundred milliseconds);
a reduction both in the damage caused by the fault and in the interferences in the power supply system;
a reduction in the thermal and dynamic stresses on the components of the installation;
a very high number of selectivity levels.

However:

it is more burdensome both in terms of cost and of complexity of the installation;
it requires an auxiliary supply.

As a result, this solution is mainly used in systems with high rated current and short-circuit current values and with binding requirements for safety and service continuity. In particular, examples of logical selectivity are often found in the primary distribution switchgear placed closely on the load side of transformers and generators.

This type of selectivity can be realized:

between Emax 2 air circuit-breakers equipped with Ekip Touch and Ekip Hi-Touch trip units.
The ultimate selectivity limit which can be obtained is equal to the Icw
Is = Icw

between Tmax T4L,T5L and T6L moulded-case circuit-breakers equipped with PR223 EF trip units.
The ultimate selectivity limit which can be obtained is 100kA
Is = 100kA

Then, by means of S51/P1 contact module, it is possible to make a chain of zone selectivity between Tmax and Emax 2. It is also possible to realize a selectivity chain including ABB MV protections.

The operating principle of zone selectivity between ABB circuit-breakers is as follows:
In the presence of current values higher than their setting, each protection sends a lock signal (by means of a direct connection or a bus) to the hierarchically higher level protection (on the supply side in relation to the power flow direction) and, be-fore tripping, checks that an analogous lock signal has not arrived from the load-side protection. In this way, only the protection immediately to the supply side of the fault trips.

Saiba mais sobre

Curves

SOC

Produtos relacionados

Fuse links

Fusíveis

Chaves fusíveis de operação manual

Select region / language

Europe
Americas
Middle East and Africa
Asia and Oceania

Global - English
Austria - German
Belgium - Dutch | French
Bulgaria - Bulgarian
Croatia - Croatian
Czech Republic - Czech
Denmark - Danish
Estonia - Estonian
Finland - Finnish
France - French
Germany - German
Greece - Greek
Hungary - Hungarian
Ireland - English
Italy - Italian
Latvia - Latvian
Lithuania - Lithuanian
Luxembourg - French
Netherlands - Dutch
Norway - Norwegian
Poland - Polish
Portugal - Portuguese
Romania - Romanian
Russia - Russian
Serbia - Serbian
Slovakia - Slovakian
Slovenia - Slovenian
Spain - Spanish
Sweden - Swedish
Switzerland - French | German | Italian
Turkiye - Turkish
United Kingdom - English

Global - English
Argentina - Spanish
Aruba - Spanish
Bolivia - Spanish
Brazil - Portuguese
Canada - English | French
Chile - Spanish
Colombia - Spanish
Costa Rica - Spanish
Dominican Republic - Spanish
Ecuador - Spanish
El Salvador - Spanish
Guatemala - Spanish
Honduras - Spanish
Mexico - Spanish
Panama - Spanish
Peru - Spanish
Puerto Rico - Spanish
United States of America - English
Uruguay - Spanish

Global - English
Algeria - English | French
Angola - English | French
Bahrain - English | French
Botswana - English | French
Cameroon - English | French
Côte d'Ivoire - English | French
Egypt - English | French
Ghana - English | French
Israel - Hebrew
Jordan - English
Kenya - English | French
Kuwait - English
Lebanon - English
Madagascar - English | French
Mali - English | French
Mauritius - English | French
Morocco - English | French
Namibia - English | French
Nigeria - English | French
Oman - English
Pakistan - English
Palestine - English
Qatar - English
Saudi Arabia - English
Senegal - English | French
South Africa - English
Tanzania - English | French
Tunisia - English | French
Uganda - English | French
United Arab Emirates - English
Zambia - English | French
Zimbabwe - English | French

Global - English
Australia - English
Bangladesh - English
China - Chinese | English
India - English
Indonesia - English
Japan - Japanese
Kazakhstan - Russian
Malaysia - English
Mongolia - Mongolian | English
New Zealand - English
Philippines - English
Singapore - English
South Korea - Korean
Sri Lanka - English
Taiwan (Chinese Taipei) - Chinese - Traditional
Thailand - English
Vietnam - English

Configurações de privacidade abb.com

Nosso site utiliza cookies que são necessários para o funcionamento do site e para fornecer os serviços solicitados. Também gostaríamos de definir os seguintes cookies opcionais no seu dispositivo. Você pode alterar essas configurações a qualquer momento clicando em "Alterar configurações de cookies" na parte inferior de qualquer página. Para obter mais informações leia nosso aviso de privacidade.

Análise

Coletamos estatísticas para entender quantos visitantes o site recebe, como nossos visitantes interagem com o site e como podemos melhorá-lo. Os dados coletados não confidenciais.

Preferência

Armazenamos as escolhas que você fez para que sejam lembradas nas visitas, a fim de proporcionar uma experiência mais personalizada.

Publicidade e rastreamento

Seu comportamento de navegação é rastreado em sites por provedores de serviços de publicidade e redes sociais. Você pode ver publicidade e conteúdo personalizados em outros sites com base no seu perfil de navegação.

Show details

Hide details

leia nosso aviso de privacidade.

Aceitar selecionados

Recusar Todos

Aceitar Todos

Seletividade com fusíveis

Como obter seletividade com fusíveis

Fusível / Fusível

Disjuntor / Fusível

Fusível / Disjuntor

Fusíveis a montante e a jusante

Disjuntor a montante e fusível a jusante

Fusível a montante e disjuntor a jusante

Zone selectivity

Saiba mais sobre

Produtos relacionados

Configurações de privacidade abb.com​

Configurações de privacidade abb.com